• Andere Unternehmen von Fluke:
  • Fluke
  • Fluke Biomedical
  • Fluke Networks
  • Fluke Process Instruments
Weitere Marken von Fluke
Accelix Amprobe Beha-Amprobe Comark Emaint Landauer Pacific Laser Systems Pomona RaySafe Schad
Startseite
Precision, Performance, Confidence.
Fluke Calibration: Europe
  • Registrieren
  • Anmelden
  • Contact Us

EU - German (Deutsch) [Change]

 

Manual approach to test a pressure switch

Manual Pressure Switch Testing

Accurate calibration of pressure switches is a critical step in ensuring process quality and the safe operation of equipment. The setup is similar to pressure gauge calibration except now a voltage or continuity across a set of switch contacts needs to be read either by a (Digital Multimeter) DMM or the calibrator. The purpose of the calibration is to detect and correct errors in the set point and deadband of the pressure switch. Calibrators can save you time by reducing steps and reducing the amount of equipment you have to bring to the job. With the right calibrator, the entire process can be automated.

To perform the test:

  • Setup
    • 1. Safely disconnect the device from the process it controls.
    • 2. Connect the calibrator or DMM to the common and NO (normally open) output terminals of the switch. The DMM or calibrator will measure an "open circuit". if measuring continuity. If measuring V ac be sure the tool is properly rated for the voltage being measured.
    • 3. Connect the pressure switch to a pressure source such as a hand pump connected to a gauge.
  • Rising pressure
    • 4. Increase the source pressure to the setpoint of the switch until the switch changes state from open to close. Manually record the pressure value when the DMM indicates a "short circuit" or if using a calibrator it will record the value for you.
  • Falling pressure
    • 5. Continue to increase the pressure until the maximum rated pressure. Slowly reduce the pressure until the switch changes state again, and resets from closed to open, then record the pressure.
  • Calculation
    • 6. The setpoint pressure was recorded when the pressure was rising. The deadband value is the difference between the rising setpoint pressure and the falling pressure reset point.

Recommended Resources

Pressure Calibration Applications and Solutions

Recommended Products

Fluke 754 Documenting Process Calibrator-HART

Fluke 719Pro-300G Electric Pressure Calibrator

  • Printer-friendly version »
  • Startseite
  • Produkte
    • Neue Produkte
    • Elektrische Kalibrierung
      • Elektrische Normale
      • Kalibratoren
      • Tischmultimeter
      • Software für elektrische Kalibrierung
    • HF-Kalibrierung
      • HF-Referenzquellen
      • Zubehör für die HF-Kalibrierung
      • Kalibriersoftware für DC-, NF- und HF-Anwendungen
    • Datenerfassung und Testgeräte
      • Labor- und Tischmultimeter
      • Messdatenerfassung
      • Funktions- und Signalgeneratoren
      • Messdatenerfassungssoftware
    • Temperaturkalibrierung
      • Primäre Normale
        • ITS-90 Fixpunktzellen
        • Platinwiderstandsthermometer-Normale
        • Erhaltungsvorrichtungen
        • Flüssigstickstoff-Vergleichskalibrator
        • Widerstandsbrücken
        • Widerstandsnormale
      • Kalibrierbäder
        • Kompakte Kalibrierbäder
        • Standard-Kalibrierbäder
        • Bäder für spezielle Anwendungen
        • Kalibrierbadzubehör
        • Temperaturregler für Kalibrierbäder
        • Kalibrierbadflüssigkeiten
        • Kundenspezifische Kalibrierbäder
      • Temperaturkalibratoren für die Industrie
        • Portable Blockkalibratoren für metrologische Anwendungen
        • Blockkalibratoren für metrologische Anwendungen
        • Hand-Blockkalibratoren
        • Mobile Blockkalibratoren
        • Mikrobäder
        • Infrarotkalibratoren
        • Blockkalibratoren für Thermoelemente
        • Doppelkammer-Blockkalibrator
        • Nullpunkt-Blockkalibrator
      • Sonden/Sensoren
        • Platin-Widerstandsthermometer (PRTs)
        • Thermistoren
        • Normal-Thermoelemente
      • Thermometer mit Digitalanzeigen
      • Multifunktionskalibratoren
      • Software für die Temperaturkalibrierung
    • Feuchtekalibrierung
      • Feuchtegeneratoren
      • Datenlogger und Überwachungsgeräte für Feuchte
    • Druckkalibrierung
      • Kolbenmessgeräte
        • Kolbenmanometer für Metrologieinstitute
        • Absolutdruck-Kolbenmanometer
        • Pneumatische Kolbenmanometer für hohe Drücke
        • Hydraulische Kolbenmanometer
        • Zubehör für Kolbenmanometer
      • Controller/Kalibratoren
        • Niederdruckregler und -kalibratoren
        • Pneumatische Druckregler und -kalibratoren
        • Pneumatische Hochdruck-Gasregler und -kalibratoren
        • Hydraulische Regler und Kalibratoren
      • Druckmonitore
        • Niederdruckmonitore
        • Digitale Druckmanometer
        • Referenzdruckmonitore
      • Druckwaagen
        • Pneumatische Druckwaagen
        • Druckwaagen mit Medium Öl
        • Druckwaagen mit Medium Wasser
        • Hydraulische Hochdruckwaagen
        • Zubehör für Druckwaagen
      • Manuelle Kalibratoren und Monitore
        • Druckkalibratoren
        • Regelung des pneumatischen Drucks
        • Hydraulische Vergleichstestpumpen
      • Handheld Pressure Calibrators
      • Luftdaten-Kalibrierung
      • Messgeräte zur Überwachung der Umgebungsbedingungen
      • Druckkalibrierungszubehör
      • Benutzerdefinierte Druckkalibriersysteme
      • Software zur Druckkalibrierung
    • Durchflusskalibrierung
      • Gasdurchflussnormale
      • Gasdurchflusszubehör
      • GFS Primärer gravimetrischer Strömungsstandard
      • Durchflusskalibriersoftware
    • Prozesskalibratoren
      • Temperaturkalibratoren
        • Tragbare Temperaturkalibratoren
        • Blockkalibratoren und Mikrobäder
        • Digitale Präzisionsthermometer
        • Temperaturmessfühler
        • Infrarotkalibratoren
        • Hygro-Thermometer mit Datenprotokollierung
      • Druckkalibratoren
        • Digitale Druckkalibratoren
        • Tragbare Druckkalibratoren
        • Druckwaagen
        • Digitale Präzisionsmanometer
        • Handpumpen zur Kalibrierung
      • Multifunktionskalibratoren
      • Kalibratoren für mA-Stromschleifen
      • Prozesskalibrierungs-Software
    • Kalibriersoftware
      • MET/CAL-Software
      • MET/CAL-Support
      • Bestandsverwaltungssoftware
      • Software für die Temperaturkalibrierung
      • Druckkalibrierungssoftware
      • Durchflusskalibriersoftware
      • Software für die mechanische/dimensionale Kalibrierung
    • Service und Support
    • Alle Kalibriergeräte
    • Hand-Messgeräte
  • Kaufinfo
    • Bezugsquellen
    • Angebot anfordern
    • Anforderung einer Präsentation
    • Anforderung einer Beratungsleistung
    • Certified Pre-Owned Equipment
    • General Services Administration (GSA)
    • Financing Program
    • National Stock Numbers (NSNs)
    • Payment Options and Tax Info
  • Aktuelles
    • Pressemitteilungen
    • Aktionen
    • Branchenverbindungen
    • Metrology Salary Survey
  • Schulung/Veranstaltungen
    • Messen und Seminare
    • Schulungskurse (in USA)
    • User Group Meetings
    • Web Seminare
      • Live-Seminare
      • On-Demand Seminare
  • Literatur/Ausbildung
    • Education Hub
    • About Calibration
    • Artikel und Ausbildung
    • Produktliteratur
    • Produkthandbücher (Bedienungsanleitungen)
    • Videos und virtuelle Demos
    • Ressourcencenter
    • Blog
  • Service/Unterstützung
    • Service Request (RMA)
    • Serviceprogramme
    • Technischer Support
    • Wissensbasis
    • Akkreditierung
    • Autorisierte Servicezentren
    • Calibration Certificates
    • Community Forum
    • My MET/SUPPORT
      • Activate
      • Procedures
      • Software
      • Technical Bulletins
      • Priority Support
      • Manuals
    • Produkthandbücher (Bedienungsanleitungen)
    • Produkte registrieren
    • Sicherheitsdatenblätter (SDS)
    • Recyclingprogramm
    • Safety, Service, and Product Notices
    • Gewährleistungen
    • Software-Downloads
  • Über uns
    • Kontakte
    • Besuchen Sie uns
    • Fluke Calibration
      • Hart Scientific Temperaturkalibrierung
      • DH Instruments Druck- unde Durchflusskalibrierung
      • Pressurements Druckkalibrierung
      • Ruska Druckkalibrierung
    • Karriere
    • Fluke Tochterunternehmen
    • Integrität und Konformität
    • Häufig gestellte Fragen
    • Why Buy From Fluke Calibration?
Startseite|Blog|Manual approach to test a pressure switch

Wir hätten gerne Ihr Feedback
Sie können uns dabei helfen, diese Website zu verbessern.

Vielen Dank!

©1995-2021 Fluke Corporation
             

Secondary menu

  • Disclaimer
  • Datenschutz
  • Webmaster
  • Terms of Use
  • Allgemeine Verkaufsbedingungen